甲烷浓度对碳化硅基底金刚石薄膜摩擦性能影响

利用热丝化学气相沉积法(HFCVD)在碳化硅基底上制备金刚石薄膜,采用场发射扫描电子显微镜、拉曼光谱仪、原子力显微镜研究了在不同甲烷浓度条件下制备的金刚石薄膜表面形貌及物相组成,在干摩擦条件下通过往复式摩擦磨损实验测试并计算了已制备金刚石薄膜的摩擦系数和磨损率,结合物相分析及摩擦磨损实验结果分析了甲烷浓度的改变对金刚石薄膜摩擦磨损性能的影响。结果表明,由于甲烷气体含量的升高,金刚石薄膜结晶质量下降,薄膜由微米晶向纳米晶转变。摩擦磨损实验结果显示:3%甲烷浓度条件下制备的金刚石薄膜耐磨性较好,磨损率为2.2×10^-7 mm³/mN;5%甲烷浓度条件下制备的金刚石薄膜摩擦系数最低(0.032),磨损率为5.7×10^-7 mm³/mN,制备的金刚石薄膜的耐磨损性能相比于碳化硅基底(磨损率为9.89×10^-5 mm³/mN)提升了两个数量级,显著提高了碳化硅基底的耐磨性。     

Characterization of ZnO:AI films deposited by r.f.magnetron-sputtering at low temperature

Transparent conducting ZnO:AI thin films with good adhesion and Iow resistivity have been prepared on organic substrates and Coming 7059 glass substrates by r.f. magnetron-sputtering technique at Iow substrate temperature (25-210℃). Structural and photoelectric properties of the deposited films are investigated. The deposited films are polycrystalline with hexagonal structure and a preferred orientation with the c-axis perpendicular to the substrate. Only the (002) peak is observed.High quality films with resistivity as Iow as 1.0 x 10- 3Ω@ cm and 8.4 x 10- 4Ω@ cm, the average transmittance over 74% and 85% in the wavelength range of the visible spectrum have been obtained on different substrates.     

Growth studies of m-GaN layers on LiAlO2 by MOCVD

This paper reports that the m-plane GaN layer is grown on （200）-plane LiAlO2 substrate by metal-organic chemical wpour deposition （MOCVD） method. Tetragonal-shaped crystallites appear at the smooth surface. Raman measurement illuminates the compressive stress in the layer which is released with increasing the layer＇s thickness. The high transmittance （80%）, sharp band edge and excitonic absorption peak show that the GaN layer has good optical quality. The donor acceptor pair emission peak located at -3.41 eV with full-width at half maximum of 120 meV and no yellow peaks in the photoluminescence spectra partially show that no Li incorporated into GaN layer from the LiAlO2 substrate.     

Analysis of end point vibrations of a two-link manipulator by integrated CAD/CAE procedures

In this work, the effect of flexibility on the trajectory of a planar two-link manipulator is studied using integrated computer-aided design/analysis (CAD/CAE) procedures. The solid models and finite element models of the parts of the manipulator are created by using the CAD/CAE software I-DEAS. The assembly is defined, and knowing the payload and the end point trajectory, the velocities and accelerations of the parts, joint forces and driving torques are calculated using the rigid body dynamics. All the time dependent nodal forces acting on the parts including distributed gravity and inertia forces are created in files with the I-DEAS program file format. The finite element vibration analysis of the parts is performed by I-DEAS. The end point vibrations and the deviations from the rigid-body trajectory are analyzed for different types of end point acceleration curves. A circular trajectory is considered as an example. It is observed that the precision of the manipulator can be increased by testing different end point acceleration curves without changing the trajectory and the duration of the end point work. The procedure explained in this work can be used for this purpose successfully.     

Investigation of thin-film electroluminescent structures on rough subsrates

Results of experimental investigations of the volt-brightness characteristics, frequency dependences of brightness, and the directional radiation pattern of electroluminescent MSDM, MSCM, and MSDCM emitters, where M stands for the first transparent and second nontransparent electrodes, S is a semiconductor, D is a thin-film dielectric, and C is a silicone-based composite liquid dielectric with a powdered segnetoelectric filler, developed on conventional “smooth” and rough glass substrates are presented. It is shown that electroluminescent structures on rough surfaces have a brightness approximately two times higher than that of similar structures developed on a “smooth” substrate. Ul’yanovsk State University, 42, L. Tolstoi St., Ul’yanovsk, 432700, Russia. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 4, pp. 507–512, July–August, 1997.     

Si衬底上ZnSe外延膜的低压MOCVD生长

以硒化氢（H2Se）和二甲基锌为源材料，生长温度是300℃时，用低压金属有机化学气相沉积（LP－MOCVD）系统在Si(111)衬底上外延生长了ZnSe薄膜。通过X射线衍射（XRD）、扫描电子显微镜的能量色散（EDS）以及光致发光（PL）实验验证ZnSe外延膜的质量，在X射线衍射谱中只有一个强的ZnSe(111)面衍射峰，这说明外延膜是（111）取向的单晶薄膜，在能量色散谱中除了Si,Zn和Se原子外，没有观测到其他原子，说明ZnSe外延膜中杂质含量较少。ZnSe外延膜中Zn/Se原子比接近1，有较好的化学配比。在ZnSe外延膜的77K光致发光谱中没有观测到与深中心发射相关的发光峰，表明ZnSe外延膜的晶格缺陷密度较小。77K时的近带边发射峰447nm在室温时移至465nm附近。     

基片光学特性对薄膜光强透过谱的影响

在考虑基片与空气界面反射率以及基片吸收不能忽略的情况下，对常见的基片上薄膜的光强透过率公式进行了修正，导出了该情况下的透过率公式．以非晶硅薄膜为研究对象，采用模拟计算说明基片光学特性对薄膜光强透过谱的影响．     

4英寸热氧化硅衬底上磁性隧道结的微制备

就如何在4英寸热氧化硅衬底上沉积高质量的磁性隧道结纳米多层薄膜材料和如何利用光刻方法微加工制备均匀性较好的磁性隧道结方面做了初步研究，并对磁性隧 道结的磁电性质及其工作特性进行了初步测量和讨论.利用现有的光刻设备和工艺条 件在4英寸热氧化硅衬底上直接制备出的磁性隧道结，其结电阻与面积的积 矢的绝对误差在10% 以内，隧穿磁电阻的绝对误差在7% 以内，样品的磁性隧道结性质具有较好的均匀性和一致性，可以满足研制磁随机存储器存储单元演示器件的基本要求. 关键词： 磁性隧道结 隧穿磁电阻 磁随机存储器 4英寸热氧化硅衬底     

Homogeneous immunoassays

Applied Biochemistry and Biotechnology -     

八信道高温超导多路器的实验研究

文中首先分析八信道高温超导多路器设计的方案,以及实现八信道高温超导多路器的技术;给出了用MgO基片为衬底,YBCO超导膜制备的高温超导滤波器设计仿真曲线及实际测试曲线;并对多路器所用制冷器的制冷量进行了计算;最后给出八信道高温超导多路器的实际测试曲线。